Item |
Part No. |
Description |
1 |
RK11888 |
T-handle, thread is 9/16”-18 SAE |
11350 |
T-handle O-ring |
11003 |
T-handle Gasket, Nylon (FE/FF) |
2 |
RK11005B |
Standard Lid |
11007 |
Square-cut Gasket (Lid & Bowl ring) |
RK11005/A |
Lid, T-handle and O-ring Kit |
RK11005B-02 |
Lid w/ Vent Port and Plug Kit (not shown) |
3 |
RK11021 |
Outer Cylinder |
4 |
2020SM-OR |
2 Micron Element w/ Seals |
2020TM-OR |
10 Micron Element w/ Seals |
2020PM-OR |
30 Micron Element w/ Seals |
5 |
RK11815-101 |
Body Clamp Bracket |
6 |
RK11-1767-01 |
Heater, 12 vdc, 300 watt (for use w/ body feed-thru) |
RK11-1800-01 (01) |
Heater, 12 vdc, 300 watt w/ body feed-thru |
RK11-1767-02 |
Heater, 12 vdc, 300 watt (for use w/ body feed-thru |
RK11-1800-02 (1) |
Heater, 12 vdc, 300 watt w/ body feed-thru |
7 |
11007 |
Square-cut Gasket (Lid & Bowl ring) |
11036 |
Bowl O-ring (FE only-not shown) |
8 |
RK21067 |
Body Feed-thru Assy. (for bodies w/ feed-thru port) (wire guage=14 AWG) |
RK11-1679 |
Body Feed-thru Port Plug (plastic) |
9 |
RK11026D |
Turbine Centrifuge/Conical Baffle |
10 |
RK21069 (2) |
Water Probe (for bowls with 1/2”-20 port) |
RK20126 |
Water Probe Port Plug (plastic) |
11 |
RK30488 |
Self-venting Drain (FF/FG/FGSS, See Figure 2) |
RK11746 |
Seal Service Kit for Drain #11780 (See Figure 2) |
12 |
11040 |
Bowl Drain Fitting (FE/FF, See Figure 2) |
RK11341 |
Bowl Drain Gasket Kit (11041 & 11340, not shown) |
13 |
RK11-1606 |
See-thru Bowl w/ Water Probe Port & Plug |
RK11734 |
Metal Bowl with 1/4”NPT Drain & Plug (FGM) |
RK11734-01 |
Same as above but with Water Probe Port & Plug |
14 |
RK11028B |
Check Ball and Seal |
15 |
RK11542 |
Hex/Washer Head Capscrew, 1/4”-20 x 1” (4) |
16 |
RK11037A |
Bowl Ring, 5” diameter (FF/FG) |
17 |
RK11-1678 |
Body, 7/8”-14 SAE w/ Heater Feed-thru Port |
18 |
RK11-1775 |
Return Tube w/ straight (body-end) threads |
RK11008 |
Return Tube w/ tapered pipe (body-end) threads |
19 |
RK11-1404 |
Assembly Seal Service Kit (all models-not shown) |
19472 |
Installation Instructions, 900/1000 Series |
(1) Filter body must have port next to fuel Inlet for heater feed-thru
installation. In-filter heater may require a Heater Relay Kit. Power requirements are (maximum) : 12vdc=25amps, 24vdc=12.5amps.
(2) Water Probe must be used with a Water Detection Kit.
See Accessories Section. |
