Item |
Part No. |
Description |
1 |
RK11888 |
T-handle (FG/FGSS only), thread is 9/16”-18 SAE |
11350 |
T-handle O-ring (FG) |
11003 |
T-handle Nylon Gasket (FE/FF-not shown) |
2 |
RK15078 |
Lid (FG/FGSS/FGMSS) |
15005 |
Lid Gasket (all models) |
3 |
RK15377-01 |
Body, 3/4”-16 UNF fuel ports (FG, effective 1/15/96) |
RK15377-02 |
Body, 16M x 1.5 fuel ports (metric, effective 1/15/96) |
RK15377-03 |
Body, 3/8”-18 NPTF fuel ports (effective 1/15/96) |
RK15082 |
Body, 9/16”-18 UNF fuel ports (FF/FG) |
4 |
2010SM-OR |
2 Micron Element w/ Seals |
2010TM-OR |
10 Micron Element w/ Seals |
2010PM-OR |
30 Micron Element w/ Seals |
5 |
RK15310-01 |
Heater, 12 vdc, 150 watt (for use w/ body feed-thru) |
RK15383-01 (1) |
Heater, 12 vdc, 150 watt w/ body feed thru (item 8) |
RK15310-02 |
Heater, 24 vdc, 150 watt (for use w/ body feed thru) |
RK15383-02 (1) |
Heater, 24 vdc, 150 watt w/ body feed-thru (item 8) |
6 |
RK15090 |
Mounting Bracket w/ Attached Bowl Ring (FG) |
RK15035 |
Bowl Ring (FE/FF/FGSS-not shown) |
7 |
15374 |
Bowl Gasket (supercedes 15009 O-ring-All models |
8 |
RK21067 |
Body Feed-thruAssembly (for bodies w/ feed-thru port) (wire guage=14 AWG) |
9 |
RK15013D |
Turbine Centrifuge / Conical Baffle (All models) |
10 |
RK21069 (2) |
Water Probe (for bowls with 1/2”-20 UNF port present) |
RK20126 |
Water Probe Port Plug (plastic) |
11 |
RK30488 |
Self-Venting Drain (FF/FG/FGSS,See Figure 2) |
11040 |
Bowl Drain Fitting (FE/FF,See Figure 2) |
RK11341 |
Bowl Drain Gasket Kit (11041 & 11340-not shown) |
12 |
RK15279 |
See-thru Bowl w/ Water Probe Port & Plug |
RK15301 |
Metal Bowl with 1/4”NPT drain threads (FFM/FGMSS) |
13 |
RK15010B |
Check Ball w/ Seal (All models) |
14 |
RK15081-01 (3) |
Phillips Head Capscrews 10-24 x 1” (4) |
RK15081 (3) |
Hex/Washer Head Capscrews 10-24 x 7/8” (4) |
15 |
RK15079 |
Standard Return Tube |
16 |
RK15300 |
Mounting Bracket, 3-piece Clamp Type (FGSS/FGM) |
17 |
RK15211 |
Assembly Seal Service Kit, All models (not shown) |
RK11746 |
Seal Service Kit for Drain #11780 (See Figure 2) |
15332 |
Installation Instructions, 500 Series |
(1) Filter body must have port next to fuel Inlet for heater feed-thru
installation. In-filter heater kits may require a Heater Relay Kit. Power requirements are (maximum) : 12vdc=12.5amps, 24vdc=6.3amps.
(2) Water probe must be used with a Water Detection Kit.
(3) Models built prior to 2/96 use RK15081-01, after 2/96 use RK15081. (The fuel ports have a 1 1/4” square boss on
models made after 2/96).
(4) Replace with 30488 drain valve.
See Accessories Section. |
